Glass for a V.I.P. – Very Important Polar bear

G.James Glass supply for Polar Bear Cub Viewing Panel

Polar bears are one of the most popular bears that we endear ourselves to.  Large and cuddly, yet so fierce. It is with fascination and awe that we can look on these creatures and catch a glimpse into their lives. Here in Australia, you can only do this from a viewing platform that has a clear, wide and very secure glass barrier.

With news of the resident female polar bear, Leah’s, pregnancy, Sea World engaged the builders, Astute assist them with the construction of a new polar bear enclosure. G.James Glass & Aluminium were sought for the supply of the glass viewing panels.

A new addition to the Sea World Polar Bear family

Leah has been living with Nelson and Hudson (who are twin brothers) in a large enclosure at Sea World. The prospect of the cub came as a little surprise, as Leah was not known to be pregnant until late into her 8 month gestation period.  Cub twins were born in May 2013 to Leah and father, Nelson. Unfortunately, only one has made it to this age, but Henry is doing very well. A new enclosure was required as the mother and cub needed to be separated from the male bears. Leah needs to care for her offspring and males have been known to try and eat cubs.

Designing a New Enclosure

Work on a new enclosure was started immediately. The planning and layout for the enclosure began 10 years ago, but the final design still needed to be resolved.  It was done in cooperation with the polar bear keepers, Sea World officials and biology professionals to ensure the safety and well being of the new inhabitants.

The majority of the enclosure is concrete and timber with the glass viewing panel making up the majority of one wall – all products need to be non toxic. The layout was designed to be aesthetically reminiscent of a polar bears natural habitat and in keeping with the existing enclosure.  It includes two ice wells (ponds where ice can be left for exploration and play), a waterfall, chilled sea water pool, trees and three cooling misters. The pool has loops in the bottom of it which toys can be attached to for the polar bears to play with.

The polar bear entrance is a wide area that is partially hidden from the viewing area, and so rocks have been strategically positioned to discourage the polar bears from hiding in this corner.  This area was in its final stages of preparation when we visited, and mobile scaffolding made by QuickAlly Access Solutions was being used to support the workers completing the job.

The more serious aspects of the pen are an isolated waste catching system, security door locking mechanisms, and a safety escape niche. Polar Bears are never tamed. Keepers cannot be in an enclosure with them, as they are at risk of being attacked.   The security door prevents the polar bear door to open while keepers are in the enclosure, and in case of failure, the niche only fits a person, and has an alarm button in it to highlight help is required.

The risk factor when in close quarters with bears makes the viewing panel not only important for visitors, but it is the only area they can be easily watched by their keepers at eye level.  All photography for recording the animals behaviour and publicity purposes are taken through this panel.

The Viewing Panel

The type of glass used in the polar bear enclosure is specified. The glazing has to be thick and secure enough to ensure the safety of the polar bears, and visitors. Four layers of glass, laminated together ensure this. The glass is around 40mm thick and each of the 8 viewing panes weigh 495kg. Polar bears will scratch at the glass, and these scratches need to be polished out every couple of years. The edges of the glass, and gaps in between need to be specially designed. Polar Bears will test edges and explore gaps, so they are constructed to minimise their ability to grip and claw areas.

On completion of the enclosure, officials from the Australian Institute of Marine Science inspect the final result. Any potential hazards or dangerous surfaces are highlighted and addressed prior to the polar bears being introduced to their new surrounds.

The Cubs Entrance to Public Life

Leah has been monitored daily since the birth of her cubs. She was living in her “maternity ward” and exercising in a special enclosure for the polar bears until September. Her new home was opened to her in mid September, and it was expected she would explore it for a week or two before she and the cub were comfortable with their new surroundings.  It has since been opened to the public.

G.James Glass supply for Polar Bear Cub Viewing Panel

In Comparison to a Wild Life

In the wild, a mother will lie in a dormant state (similar to hibernation) in a den made inland of snow and ice for about the second half of the gestation period. After birth, the cubs are reared in the den for the first couple of months of their lives before being introduced to the world. The cubs have about 2 weeks to gain their strength and learn to walk over distance and run before journeying to the sea. They spend between 1 ½ and 2 ½ years with their mother before going out on their own.

Click on the images for more Polar Bear facts.

Glass By Definition – Part 1

Glass Bike - Glass Definitions - G.James Glass and AluminiumThis article will assist in demystifying the types of architectural glass used in buildings. The names we use for the different glass types are generally attributed to some part of the manufacturing process. In part one of this two part series, we look at basic glass products to highly processed glazing options.

Some History on Architectural Glass

Since clear glass was being first made in about 100 CE, in Alexandria, the Romans began using it architecturally. This began the long list of manufacturing methods and specialised names attributed to the different types of processes – Broad sheet, Crown, Polished Plate, the list goes on. In 1848, a crude form of float glass was patented by inventor Henry Bessemer by pouring glass onto liquid tin, but it was very expensive. It wasn’t until 1959 that this idea for float glass was made in a practical method – a discovery by Sir Alistair Pilkington that now dominates the worldwide commercial production of architectural glass products.

Basic Float Glass Products

The differences between the basic glass types are formed in the glass making “float process”. Soda, lime and silica as well as broken glass called cullet are the major components used in the manufacture of glass. These components are mixed into a batch before being heated to approx. 1500°C in a furnace. The molten glass is then floated on a “tin bath” –  a layer of molten tin.   As the glass begins to cool it solidifies and is drawn out of the float tank in one continuous ribbon.  The glass enters the annealing or cooling lehr – it is the controlled cooling (annealing) of the glass that allows it to be cut and further processed.

Float Glass or Annealed Glass

These terms are interchangeable and refer to the respective glass manufacturing processes.  They describe glass in its basic form, before secondary manufacture.  In a general sense, Annealed Glass is used when comparing heat treated glass to non heat treated glass.

Clear Glass

Clear Glass is a piece of transparent float glass, typically uncoloured.

Tinted Glass

Tints are glass with metal oxides added to give it a specific hue. The tint or colouration is through the body of the glass and therefore darkens with an increase in thickness.  Apart from aesthetics, tinted glass is used for reducing heat gain through the glazing system. Common tints include green, blue, grey and bronze.

Super Tints

Super Tints are designed to reduce heat gain while allowing the maximum amount of light through making it a performance product. The heat absorbing qualities also make them prone to thermal stress (caused by temperature difference), and a thermal safety assessment is recommended to determine if heat treating is required (see Secondary Manufacture below). Colours include Azuria, Super Green and Super Blue.

On Line Coated Glass

Sometimes referred to as pyrolytic glass, metallic oxides are deposited onto the glass surface in the float glass tank during manufacture. These coatings can increase the performance of the glass with a range of reflective and low E products available. They are extremely hard and durable, and can be used on their own or heat treated without affecting the coating.

Low Iron Glass

The green colouration in glass is due to the iron content found in silica or sand. Low Iron Glass has less than 1/10th of the iron content of standard glass and are considered ultra clear. Low Iron Glass is ideal for use in display cases, painted glass applications like splash backs or in areas where high clarity is required.

Deli Bend or Curved Glass (Annealed)

Glass can be curved as float, by laying the glass over a mould before annealing begins. It is commonly used to make butcher or delicatessen benches (hence the name), furniture and curved architectural glass that is to be laminated.

Processed Glass

Glass requires finishing before it can be used in location, or sent for secondary manufacture. Commonly, this includes cutting to size, and edging, but there are many alternatives in both these fields.

Cutting

Almost all glass will require cutting to the job size requirements, but this process also includes cuts to produce as irregular shapes, such as raked windows, shower screens with cut outs for fittings, glass walls needing spider fittings and custom profiling.

  • Various regular and irregular shapes required are cut with a CNC machine.
  • V Grooved cuts in the face of glass, or brilliant cut, provides an alternate decorative finish.
  • Drilling – Holes from 5mm to 100mm can be drilled into the glass, but the hole diameter must be equal to or greater than the glass thickness. Holes can include a countersunk rim. The hole edging has a ground finish.
  • Shaping – glass can be cut at special shapes or profiles to custom requirements.

There are edge clearances that are relative to the glass thickness for the size and location of cut outs and holes drilled into a sheet of glass. Please contact your manufacturer for exact positioning limitations.

Edging

Edging provides a range of options for the perimeter of the glass to suit its application. Different edges are applied for ease of installation, to assist with further processing or to achieve a look.  One common process is arrissing – a term used to describe the method used to grind the sharp edges of glass to make them safer to handle.

  • Plain cut glass, is called Clean Cut
  • Glass to be toughened requires Rough Arris edge work – arrissed edges with a rough ground finish.
  • Smooth Arris is similar to the rough arris, but with a smoother finish to the edge.
  • Flat Grind or Flat Smooth edges are machined smooth edges suitable for silicone butt jointed applications.
  • Flat Polished is the neatest finish used for exposed edges of glass.
  • Mitred Glass has a 45 degree bevel on one side with an edge finish suitable for mitred silicone butt joints.
  • Round and Polished edge work gives the glass a curved edge for exposed perimeters.

Secondary Manufacture

Secondary Manufacture takes the various types of float glass and changes the properties in a range of production processes.

Heat Treated Glass

A general term used to describe the process of further strengthening or testing glass in a second heating and cooling process. Its is the way or speed in which the glass is cooled gives the glass stronger properties, and length of heating to test the glass.

Heat Strengthened Glass

Heat strengthening is a treatment of glass that induces a high compression layer on the surface.  This is done by cooling the reheated glass at a specific rate. This process makes glass twice as strong as annealed glass, although it is not considered safety glass.

Toughened or Tempered Glass

Toughening glass also induces a high compression layer in a similar process to heat strengthened glass. To toughen the glass, the heated glass is cooled very quickly. This makes it 4 to 5 times stronger than annealed glass of the same thickness. Certain thicknesses are considered A grade safety glass – refer to standard AS 1288.

Heat Soaked Glass

Toughened glass can spontaneously shatter due to small imperfections in glass called Nickel Sulphide inclusions. They are rare, but undetectable, and so, to ensure the glass will retain its form, heat soak testing is done. The glass is heated for a period of time which induces the Nickel Sulphide inclusions to rupture if they are present.  Glass that passes the test, has a markedly reduced possibility of failure once in location.

Curved Glass (toughened)

Curved Glass that requires toughening is bent in the toughening process.  A series of rams fold the glass to the desired shape. Tighter corners and soft curves are achievable.

Off Line Coating

High performance glass has a coating applied to its surface. Different looks can also be achieved with colour and reflectivity. Although large steps in technology over the last couple of years have increased the durability of off line coatings, some are quite delicate, and cannot be heat treated.  Others need to be used in an IGU, so the coated side of the glass is sealed from the elements and physical damage.

Laminated Glass

Laminates are made of two or more pieces of glass permanently bonded together with interlayers. Interlayers are made up of various materials to give the completed glass additional properties, for example, acoustic, colour and UV eliminating. Laminated glass is considered A grade safety glass.

IGUs

IGUs consist of two panels of glass fitted together with a hermetically sealed air space in between to provide an insulative layer protecting against thermal and acoustic issues. The air in the gap is dried to prevent condensation issues.

Other common glass terms

The following terms are not processes done to manufacture glass, but are descriptions of how they are classed, rated and used.

Double Glazing

Double glazing is when two pieces of glass are used with an air gap in between. Special framing suites with glazing pockets front and back are considered double glazed, as are jockey sashes and IGUs.

Monolithic Glass

Monolithic glass is a single pane of glass as opposed to laminated, double glazed or insulated glass units.

Safety Glass

Safety glass is processed glass that is manufactured to satisfy the requirements of AS/NZS 2208 for safety glazing. Laminated and toughened glass are rated Grade A. Wired glass is rated Grade B.

Security Glass

Security Glass is designed to repel violent attack. They are usually combinations of laminated glass that incorporate toughened or polycarbonate combinations. They are not necessarily considered Safety Glass.

Part two to be released in November –

I hope you found these descriptions useful. In part two of this article, thermal glazing terms and properties will be discussed. It will include the terms used to measure and describe performance, what basis the measurements are made from and a comparison of data commonly used – glass only vs whole of window data.